A Scene in Fifteen Steps -- Step 6, a Photo Backdrop

A photo backdrop has been under consideration all along

In my previous post, I noted my notion of trying Bob Frankron's approach to completing a scene in fifteen steps. There, I listed fifteen steps to completing the Nooksack Valley produce complex spur scene. In that list, the sixth step was to add a photo backdrop a la Paul Dolkos. As I was preparing a clinic to present for my NMRA division, my focus for the last couple of weeks was on this step.

Early in my planning for this scene, I researched packing plant images, both for structures and entire scene images. In my Google image searches, I came across this site that included a photo that included the section seen to the left. This scene is fairly modern and includes modern semi-trailers, but it was the best starting point I found.

After living with the original image leaning in place, I decided to make some changes. I took a fairly analog approach. I printed out the original image and resized it to what seemed appropriate on my inkjet printer/copier/scanner. Then I printed several copies to create a collaged version of what I thought I wanted. Using a sharp number 11 blade and glue stick I made several changes by covering the trailer, removing the large fruit boxes, and extending the building to the left in my final collaged image.

I photocopied the collaged image, and after printing it out went ahead and cut out the image I planned to use, again with a sharp hobby knife. As I was working down in the train room this time, I cut on the tempered glass on my workbench.  As inkjet printed images are subject to bleeding if they get wet, I sprayed the image with several layers of Testors Dullcoat. After that protective layer dried, I used a sepia Prismacolor marker to color the white paper along the cut edges. My recommendation would be to use a light gray or sepia colored Prismacolor rather than black or a Sharpie of any color.

For this experiment I used Scotch Super 77 as the adhesive. It is a very aggressive adhesive, so make sure to protect whatever surface you are working on. I used some old packing papers and a paper towel, but still managed to get one spot on the benchwork. I had to go back with lacquer thinner to remove it. The point of using this glue is to avoid the photo peeling off later. 

Before applying the spray adhesive, I marked the location of the where I wanted the photo on the benchwork and experimented with coving the bottom of the photo onto the benchwork. After I applied the spray adhesive and let it dry to tacky, I placed the top in place. After smoothing the top edge down, I carefully smoothed down the bottom on the benchwork leaving a coved or rounded gap between the top and bottom edges. The photo to the left shows the photo glued in place, hopefully hiding the right angle between the backdrop and the benchwork with a coved image. 

The most recent step I have taken was to do some painting on the brown plywood bench top. The goal is to further hide the joint between the photo and the bench top surface. I used grimy black and a slate gray acrylic paint to blend from the ground into the photo. I blended the two colors, wet on wet, as I applied them. I am not entirely happy with the results, but the paint is just the first layer. I will be adding sanded grout, which I may apply up into the photo. Although I don't always follow my own advice, in general it is best to stop before I go too far. I remember Gerry Leone saying in a video that he "tries to stop when he thinks to himself, 'just a little more'."

 

Updates and Goals

I have updates and goals for both the train room (aka the basement) and for the railroad. 

As I left off my last post with wet basement issues, I will start with that. My wife helped me last week on one of our continuing rainy days, and we made a good start on removing the scabbed-in bar. As you can see in the photo, I still have some framework to remove. The damp floor in what I was calling "the floodplain" can also be seen. Not labeled, but suggested is the approximately one inch wide "French Drain Canal" between the green concrete floor and the yellow wall. Judging from the existing rot, the floodplain has been an ongoing issue, exacerbated by our wettest May on record. A steady stream of water was flowing into the "canal" until about ten days ago. I will need to build a lip along the floor (a levee) to prevent the canal from overflowing here in the future. 

In addition to the wet basement abatement, another goal for this summer consists of more electrical work. The sump pump and water conditioner are currently powered through a gnarly extension cord draped across the ceiling. They need a direct line. Renee wants some general lighting in the basement with a switch. I want a line to outlets for the railroad lighting (current and future) also switched. Plus our three season room's outlets need to be reconnected and a few more receptacles added in the basement. This really should be done before any significant  additions to the railroad are contemplated! We need a firm plan and easy access before we call in the professional. 

I want to continue with this area around the fruit and produce spur. I am giving a clinic soon, and I would like to try using the photo that I have propped up against the backdrop in this image and share the results. It actually isn't a straight photo; I collaged parts of the photo to make changes. The other experiment is to cove or curve the photo from mounted to the backdrop to glued to the benchtop. I will need to remember to coat the photo (printed on my inkjet printer) with a fixative so that water based scenery doesn't make the colors bleed or otherwise destroy the image.  Then I can experiment with first layers of scenery and weathering to blend the road surface onto the benchwork. 

Several years ago I attended a clinic by Bob Frankrone about completing a scene in fifteen steps, and thought I might try that approach to the fruit and produce spur area. Here is a to do list of my fifteen:

1. Last steps on brick building
2. Warehouse a la Bill Schopf (multiple steps)
3. Sand the cork edge
4. Sand the painted sky 
5. White wash for atmospheric haze
6. Photo backdrop a la Paul Dolkos
7. Sculptamold for texture
8. Paint and first layer of scenery
9. More layers of scenery 
10. Fence
11. Tie pile 
    
12. 12 volt DC lighting bus
13. Connect lights
14. Ballast spur
15. Details

In this prototype photo of the Interbay Yard in Seattle, I really like the area between the tracks in the bottom right area: a little uneven terrain, some tall grass and shrubs, and a pile of ties. This photo is from the digital library at the Cornell University. 

U.S. President's Railroad Commission Photographs