Staying On Track: Updates Continue

 

With the wiring and clean ups coming together in the basement/train room, I went ahead and unpacked the buildings from Nooksack and placed them in their intended locations. Having finished the background warehouse for the packing house scene, that area is ready for next layer of scenery such as ground cover application. However, before I jump into that I want to continue with the next phase of construction of benchwork and backdrop as it will be just to the left (west) of this scene.

Just in the last few days I picked up some 1 by lumber for benchwork construction. I started by cutting to length before glueing and screwing together some 1 x 2 and 1 x 3 boards to form an L-girder.  The back edge of the new section will rest on this L-girder shelf. I discussed this new section, designed to create some scenery and connect the Ferndale Junction module with Nooksack, in an earlier post. As implied by the placement of the L-girder shelf, the new section will continue with open grid construction. I explored a couple of other benchwork approaches, but decided to stick with open grid benchwork with a couple of adaptations. I do plan to drop part of the plywood below track level to create the bottom of a lowered ravine section of the cut and fill scene. I may also use a subtle cookie cutter technique to create a bit of incline for the yard lead track. A third adaptation will be a slightly curved front edge to this section of benchwork, anticipating future expansion plans where this area will accommodate a narrow aisle. While the benchwork here has all been pretty rectangular, I did build a curvey, multilevel section in my attic layout in Meadville. The next steps with this section include extending the backdrop and cutting the plywood (or cardboard template) to shape, so that I can finalize the track and framework plans. 

While the painting of the basement walls is still not complete, I did finish this section between the laundry area and the furnace a couple of weeks ago. If I would just knuckle down and do it, I have only one section of the exposed foam coating of the stone walls left to paint. Granted it likely will be the trickiest, with lots of pipes and other household infrastructure to work around, but it should be doable in one day's work. While the area behind the new section and Ferndale Junction's walls are painted, I should paint the floor and do any hydrostatic concrete repair before the permanent installation of those modules takes place. As I paint the walls, it just makes me more aware of how beat up and unsightly the floor appears. Prepping and painting the floor is a bit of a gumption trap, but I must bite the bullet before I make it even harder for myself by fixing more benchwork in place. 

Ingleton Updates

Ingleton with fascia and Power Cab installed

The last time I posted about bringing the Ingleton shelf back to life, I listed six items to work on in checklist form. Over the last few weeks I have completed the first two.

I saved  a piece of beveled siding that the previous owners used in the bar area of the basement to use as the fascia. After trimming it to the correct length, I couldn't decide how to best attach it to the shelf. It is seen leaning against the shelf in this photo.  Without some form of support, I was convinced that a connection between the 3/4" shelf edge and the narrow beveled edge of the fascia would be flimsy at best. Also seen in the photo is what I decided to do--I glued a 1" x 2" along the bottom of the front of the shelf. My thinking was that would give enough support to the fascia after it was screwed in place. 

Before attaching the fascia, I figured out the appropriate size opening for the NCE Power Cab throttle panel, marked it, and cut it out, remembering that I had limited wire length to work with from the existing bus wire. Also before attaching the fascia, I applied the first coat of SW Andiron, my standard fascia paint color. Then I clamped the fascia in place and attached it with drywall screws and finishing washers before applying a second coat of paint. 

Since the shelf already had the DCC bus installed, completing the installation of the Power Cab system was quite easy. The supplied wall wart cable plugs into the back and the two track wires screw into the green clip that then also slides onto the back of the panel. I found that using a white pencil to mark the screw hole locations on the fascia works best with my dark fascia color. The mounting screws are not included with the package, but I have a collection of screws on hand. I followed the NCE guideline of having the LED to the bottom and plugging the flat wire into the left port. To finish the installation after mounting the panel, I also drilled two holes in the fascia and attached dowels to hold the throttle when it is not in use. This can be seen in the initial photo at the top of the post. In that photo, one can see that a valance is needed to limit the glare from the LED lighting for the Ingleton shelf.

I am hesitant to move much beyond planning for the valance by unpacking rolling stock and structures before I have more presentation or infrastructure work done. Again, looking at the initial photo at the top of this post, more painting needs to be completed behind Ingleton's stud wall. Also, cleaning up the base of this stud wall might be connected to a desire to paint the floor. The green floor paint is starting to get pretty beat up looking. On the other hand, if the desire to run some trains becomes overwhelming, Ingleton is ready!